LM2940CT 5.0 PDF

Package. 0˚C ≤ TJ ≤ ˚C LMCT LMCT LMCT LMCT TO LMCS LMCS The LMCT/NOPB is a positive Voltage Regulator features the ability to source 1A of output current with a dropout voltage of typically V and a. Pin 5 and 6 need to be tied together on PCB board (5) ESD rating is based on the human body model, pF discharged through LMCT/NOPB.

Author: Kazrajas Nikus
Country: Mauritania
Language: English (Spanish)
Genre: Life
Published (Last): 21 October 2009
Pages: 296
PDF File Size: 13.14 Mb
ePub File Size: 6.68 Mb
ISBN: 564-4-84575-402-8
Downloads: 48302
Price: Free* [*Free Regsitration Required]
Uploader: Mezirn

During line transients, such as load dump when the input voltage can momentarily exceed the specified maximum operating volt-age, the regulator will automatically shut down to protect both the internal circuits and the load. I believe the data sheets show a 0.

LDO – LM2940CT-5.0

Keep in mind the adapter you have may lm2490ct putting out more than 9 volts, or may not have a very clean output, both of which will make the regulator get hot. Comments 10 Comments sorted by Date Added Votes. The ESR of the output capacitor will cause loop instability if it is too high or too low. Check your caps, it might be leaky.

LMct gets HOT quick. — Parallax Forums

Friday, December 05, Thank you for all the input. I can’t find a schematic of it. Otherwise the output impedance is too high and it oscillates. Text in the Subject and Body of the message will be ignored. JavaScript seems to be disabled in your browser. The power in Watts being dissipated within the regulator is the voltage drop across the regulator times the current passing through it. I like to put a led on the output for the minimum load, and to show, solidly, that power IS really on.

  CHARLES-ALBERT CINGRIA PDF

Familiar regulator features such as short circuit and thermal overload protection are also provided. Furthermore, hidden in the ap note the ones that I have seen is an admonition to have a minimum current load. Does it have a backlight? Your use of Yahoo! The only things being powered in the circuit is the stamp and the LCD.

Another data sheet says 0. Be the first one to review this product.

LMCT-5 Datasheet

Write Your Own Review Only registered customers who has bought this product can write reviews. Hi John, What is the input voltage to the regulator — can you measure it?

I accept the Terms and Coditions. I haven’t experienced it personally, but you could have an issue there that might result in overheating. If you aren’t running very much current, and your Vin isn’t too high, a small clip-on heat sink can significantly reduce the regulator’s temperature. That would work alright.

Quick Links Categories Recent Discussions. Sign In or Register to comment. First name is ml2940ct The burn your finger kind of hot. Do you know about how much output current you have? Here’s a snip from p.

  ARTIFICIAL PARADISES BAUDELAIRE PDF

It’s interesting that mine gets this hot when I have seen schematics using the same setup, with a 10uf cap even. Email to a Friend. Another, does your LCD has backlights?

Thanks, John In basicstamps yahoogroups. The LM gets hot after a few min which isn’t lm294c0t.

LM2940ct 5.0 gets HOT quick.

Should I use some other voltage regulator? Typically, LCD displays take very little, but I’m not familiar with the unit you’re using.

It is essential that the output capacitor meet these requirements, or oscillations can result. The acceptable range of ESR plotted versus load current is shown in the graph below. Did you take steps to obtain caps with appropriate ESR? My input is 9V, I’m using the power supply that came with the P40 demo board. You must have JavaScript enabled in your browser to utilize the km2940ct of this website.

Please, log in or register. Basic Stamp List Subject: There is another possibility Furthermore, a quiescent current reduction circuit has been included which reduces the ground current when the differential between the input volt-age and the output voltage exceeds approximately 3V.